Parts & Accessories

This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum

Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.

Zipp Speed Weaponry Rear Axle Conversion Kit - Not to be used on 188 V6 or earlier rear hubs - Only to be used to convert Zipp's 188 V7 10-speed rear hubs to 11-speed

Boostinators are hub specific conversions designed to take non-boost hubs and convert them to boost compatibility. Don't toss out that wheelset - Boostinate it.

Whisky Parts Co. Tubeless Rim Tape.

Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

You need rim tape to keep your tubes from blowing through the spoke holes, especially when landing big airs. WeThePeople's got your back, though. If your's is questionable, you better replace it with this WTP Nylon Rim Tape, a perfect fit with Logic Rims. - Strong - Lightweight - Tube-proof

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

Tannus Armour Tubeless inserts are the result of years of top level multi-cell foam manufacturing mixed with extensive professional riding experience. At the heart of Tannus is the patented Aither Technology; a multi-cell foam compound that forms the structure of the Armour. The inserts are designed to displace small impacts while offering a spring-like rebound for a smooth yet playful ride. - 3% Faster than standard tubeless - Flexible sidewall stabilizing "Wings" for smoother ride quality, with 50% more vibration damping - 20mm of rim protection - Not a sealant sponge – keeps sealant where it belongs - Easy Installation (5 Minutes, No tools required) - 150g - About as much as a standard tube (a little lighter)

Tannus Armour Tubeless inserts are the result of years of top level multi-cell foam manufacturing mixed with extensive professional riding experience. At the heart of Tannus is the patented Aither Technology; a multi-cell foam compound that forms the structure of the Armour. The inserts are designed to displace small impacts while offering a spring-like rebound for a smooth yet playful ride. - 3% Faster than standard tubeless - Flexible sidewall stabilizing "Wings" for smoother ride quality, with 50% more vibration damping - 20mm of rim protection - Not a sealant sponge – keeps sealant where it belongs - Easy Installation (5 Minutes, No tools required) - 150g - About as much as a standard tube (a little lighter)

Tannus Armour Tubeless inserts are the result of years of top level multi-cell foam manufacturing mixed with extensive professional riding experience. At the heart of Tannus is the patented Aither Technology; a multi-cell foam compound that forms the structure of the Armour. The inserts are designed to displace small impacts while offering a spring-like rebound for a smooth yet playful ride. - 3% Faster than standard tubeless - Flexible sidewall stabilizing "Wings" for smoother ride quality, with 50% more vibration damping - 20mm of rim protection - Not a sealant sponge – keeps sealant where it belongs - Easy Installation (5 Minutes, No tools required) - 150g - About as much as a standard tube (a little lighter)

If you make huge rims you have to make huge rim strips too, and that's exactly how Surly's Rim Strip came to be. Made of PVC and available in 3 colors it protects your tube from the inside of the rim with stylish simplicity.

- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install

- M-Pulse front axles incorporate drive-side end cap and rear axles the non-drive side end cap - Neo OS axles are steel and compatible with standard Neo hubs for riders looking for a steel option - Instructions and hub axle determinations are available

Stan's All Mountain 29er Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!

Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's Cyclocross Tubeless Kit converts standard tubed wheels to tubeless so you can reap the benefits. Everything you need to go tubeless is included. Plus, you won't miss dealing with flat tires and you'll save money on tubes!

Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's Standard Tubeless Kit converts standard tubed wheels to tubeless so you can reap the benefits. Everything you need to go tubeless is included. Plus, you won't miss dealing with flat tires and you'll save money on tubes!

Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair. Identifying your Hugo rim and selecting the correct valve stem: Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim. Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads: MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.

This conversion kit allows you to use SRAM's 11-speed mountain cassette on your Stan's NoTubes wheels. Each kit includes an XD freehub, spacer, drive side end cap, and three sealed bearings.

The Rear Wheel Cover is a critical safety component for carrying passengers on the Globe Haul ST. The easy-to-install guards cover openings on the frame and rear rack to prevent fingers, toes, and clothes from getting too close to the moving wheel and chain. They also protect from dust and grease to keep riders and bikes cleaner. **For Globe Haul ST bike customers: Use of compatible (1) footrests (pegs), (2) passenger seat, (3) passenger handlebar, and (4) rear wheel cover required to safely carry passengers. All items available separately. ** - Compatible with Haul ST. - Includes two upper fender covers and two lower wheel covers. - Easy toolless installation.

- Replacement rear wheel skewer. - Specifically designed for use with Saris trainers. - Can be used for both indoor and outdoor rides.

- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Right Axle End Cap

- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap

Yes! A 12mm thru-axle adapter for BOB Trailers. These Robert Axles for BOB Trailers are specifically engineered to attach the proven BOB Trailer to your thru-axle-equipped bike. Take full advantage of your modern bike with 12mm thru-axles and harness the rigidity of the thru-axle to haul your BOB Trailer. Set out on any adventure, big or small. Great for off-road tours, trail building, hauling cargo, and more! - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The axle ends are stainless steel which allows for mounting of the BOB Trailer bobbins. - No special tools required. The design allows for wheel installation or removal using your standard 5mm hex wrench. - Please note: This axle does not come with the BOB Trailer bobbins (those are available separately). Or, you can reuse your bobbins from the stock BOB Trailer Quick Release that came with your trailer. - Designed, built, and quality tested in the USA. Proven around the world.

Purchase our Kid Trailer axle for your bike, and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

Purchase our Kid Trailer axle for your bike. and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - This axle is specifically designed to fit the 142/148 hub standard Surly MDS or Gnot Boost bikes. - The derailleur end of our axle is internally threaded and will use the bolt from your stock Surly axle. The disc brake side of our axle has an engineered mount for your trailer hitch. That mount has been permanently attached to the axle. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. The threads are M10x1 (metric). - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.