Cables

Hydraulic hose with banjo fitting for TRP brakes.

SRAM's Guide Hydraulic Line Kit is a replacement hose kit for all Guide brakes. - Compatible with SRAM Guide R, RS, RSC, and DB5 brakes - Length: 2000mm

Replacement line kit for SRAM and Avid hydraulic disc brakes. - For Level Ultimate/Level TLM (A1), 2018+ CODE R/RSC (B1) - 2000mm, black

Original equipment hydraulic hoses for no-compromise brake performance. - Hose Use: Front, Rear - Black - 2000mm hose length - Compatible with SRAM road hydraulic disc brakes

Original equipment hydraulic hoses for no-compromise brake performance. - 2000mm, black

Fittings for converting open loop housing holders on a frame to traditional cable stops. - Fits snugly inside open loop and receives 5mm housing with no end cap - Large flange for larger hydraulic loops - Flattened on one side to accommodate frame

Jagwire's Brake Noodles feature stainless-steel tubes with aluminum ends for durability and excellent performance. You get 10 of them for all your bicycle setup needs.

Jagwire's C-Clips are little nylon clips designed for use with Jagwire's Stick-On Guides (sold separately) and compatible frame cable guides. The C-Clips fit over your housing and hydraulic lines and snap into the guides to keep the lines in place, tidy and operating smoothly.

Jagwire's Cable Grips are adapters that make it possible to run hydraulic brake lines on bicycle frames that have housing stops that were designed for regular wire cables and standard housing sections. Once the regular cables and housing sections are removed, the Cable Grips are inserted and tightened in place in the standard frame stops. Then, the hydraulic lines are attached and securely held in place by the gripping jaw(s) of the Cable Grips. - Aluminum model accepts lines up to 5mm in diameter and the lines snap in. - Stainless model grips fully around the lines and is adjustable to fit most diameters.

Jagwire's EZ Handle Single End Straddle Wire is a replacement straddle wire (also called a crossover or transverse cable) for cantilever brakes.

Jagwire's flexible shift housing is used for the rear housing segment with Shimano Shadow-type road rear derailleurs to give optimum shifting performance and the flexibility needed for wheel installation and removal. - For use with Shimano Shadow type road rear derailleurs, such as RD-R9100, RD-R8000, and RD-R7000. - 4mm low-compression CGX-SL housing construction. - Includes 10x sealed end caps and 10x 4mm/4mm housing connectors

Jagwire's M10 Adjusting Barrel is a 10 x 1.0mm-threaded replacement cable-adjusting barrel. It's the right replacement part for most mountain bike brake levers. It's made of durable metal with a lockring for locking your adjustments. You get a pack of 10.

Jagwire's Mickey Adjusting Barrels are quality adjusters that mount to most road frames. They make it easy to fine-tune your shift cable tension by hand for optimum shifting performance.

Mountain Elite Sealed shift cable & housing sets completely protect your system against dirt, mud, and debris. A fully continuous liner with upgraded Speed-Lube lubricant ensures that protection against the elements does not come at the expense of top level performance. - Polymer coated cables dramatically reduce friction - Speed-Lube ultra slick lubricant protects cable to ensure consistent performance - Sealed system prohibit grime from contaminating system and compromising shift quality - SRAM/Shimano compatible cable ends are one sided for easy installation Kit includes: - Front Cable Length: 1500mm - Rear Cable Length: 2300mm - Housing Length: 3200mm - 2 Grub Seals - 4 Open Brass End Caps - 7 Open Alloy End Caps for 5mm Housing - 2 Non-Crimp Cable Tips - 2 3G Tube Tops - 2 Rotating Hooks

Inline adjusters make on-the-fly derailleur cable tension adjustments safe and easy. - 5mm - Stronger detent mechanism for use with brake housing - Perfect for mechanical disc brakes

Road Elite Sealed brake cable and housing sets completely protect your system against dirt, mud, and debris. A fully continuous liner with upgraded Speed-Lube lubricant ensures that protection against the elements does not come at the expense of top level performance. - Polymer coated cables dramatically reduce friction - Full seals keep out corrosive agents - SRAM/Shimano road compatible cable end Kit includes: - Front Cable Length: 850mm - Rear Cable Length: 1650mm - Housing Length: 1700mm - 2 Grub Seal - 2 Open Brass End Caps - 4 Open Alloy End Caps - 2 Non-Crimp Cable Tips - 2 3G Tube Tops - 2 Rotating Hooks

Rotating S-hooks securely hold housing segments together and prevent undue noise and migration. - Two halves rotate 360 degrees - Compatible with 4mm or 5mm housings

Rotating S-hooks securely hold housing segments together and prevent undue noise and migration. - Two halves rotate 360 degrees - Connects 4mm or 5mm housing to electronic shift wire

Jagwire's Sealed Shift End Caps are the important housing ferrules placed on the end of housing sections to optimize your shifting. They are available in 2 types to fit most housings and they feature small rubber O-rings to help prevent moisture and grit entering the housing and fouling your shifting. These ferrules are best used with derailleur cable and housing.

Jagwire's Sport Inline Adjusters are installed on your shift cable housing sections so that you can fine-tune the shift cable tension by hand (without tools). They're great for keeping your shifting dialed in. They're precision made of lightweight aluminum and nylon for easy use and durability. To install them, remove the cables and housing sections, cut the top housing sections in two and rejoin the sections with the Inline Adjusters in the middle.

Jagwire Sport Mineral Hydraulic Hose Kits feature a durable, flexible reinforced layer surrounding a low-friction inner tubing to deliver light brake lever action and trustworthy braking power. Offered as single hose kits for individual brakes or in bulk boxes for workshop use, Sport Mineral Hydraulic Hose is available for most popular road and mountain hydraulic disc brake systems that use mineral oil brake fluid. - High performance hydraulic hose provides effective braking power and control - Kits include hose and necessary fittings for one brake lever and caliper system - Contains 2000mm HPP hydraulic hose, needle insert, compression bushing, compression nut and seals for the listed compatible brake models - Compatible with Shimano Dura Ace (R9120, R9170), Ultegra (R8020, R8070), 105 (R7070), GRX (RX810, RX400), and similar brakes - For use with mineral oil brake systems only

Sport level brake cables come in a variety of cable end setups to fit most bikes at a quality level well above normal OEM cables. - Slick cables are die-extruded for smooth operation - Pre-stretched - SRAM/Shimano mountain compatible cable end - Stainless steel construction resists corrosion - Single end cable features weld-cut for easy installation

Jagwire's Road Brake Inner Wire is a high-quality brake cable made of stainless steel for excellent braking performance, corrosion resistance and durability. It comes in Campagnolo and SRAM/Shimano models and lengths to fit single and tandem bicycles.

Jagwire's Sport Slick Stainless Shift Cable is a high-quality shift cable made of stainless steel for excellent shifting performance, corrosion resistance and durability. It also comes in lengths to fit single and tandem bicycles.

- Wire hook for electronic shift and brake housing - 2.5mm E-Shift + 5.0mm Brake

Keep housing, hose, and electronic wires tidy with Jagwire Wire Hooks. - 4mm / 5mm hooks - Connects 4mm shift housing, dropper housing, or E-bike control wire to 5mm brake housing or hydraulic hose - Pack of 4 hooks

- Brass barrel, 2.2mm cable pass-through, screwdriver slot on both ends

- Shop dispenser of aluminum cable end caps to prevent cable fray - 500 pieces - 1.6mm

- Housing features the Jet Lube Process, which injects the proper amount of grease from end to end and results in 10 percent less cable drag - Lead and Dioxin free. - 30m - Made in Japan

- Shop dispenser of cable end ferrules - 100 ferrules per bottle - For use with 4mm housing